Featured Ride: Rob’s International Loadstar

46

The first time I saw this truck it was surrounded by rows and rows of low riders and mini trucks but the second I laid eyes on it tunnel vision took hold and everything else instantly became a blur.

I must have circled this truck at least a dozen times and stood by it for at good ten minutes and still had no idea just how much work the owner Rob put into transforming this 1977 International Loadstar from a standard work vehicle into the pavement scraper you see today.

From the front bumper back everything on this truck is the work of extremely talented fabricators and builders. The floor and firewall are completely scratch built as are the suicide door hinges, and all of the front body seams have been welded and smoothed shut to give the body cab a clean refined look.

In addition to all of the unnecessary bits being shaved from the exterior the factory 1977 lighting has been addressed all around the vehicle. On the roof pedestal mounted lights have been added and on the sides and rear the accessory lights have been swapped to LED units, last but not least HIDs now sit in the headlight position under the chrome visors replacing the factory equipped sealed beams that lived their previously.

Beneath the cab the frame is a work of art now serving double duty as the trucks 25 gallon air tank in addition to its backbone. The 3 x 1/4″ wall frame has been completely sealed shut allowing air to travel through it to the 10, 000lb transport truck air bags via 3/8″ steel half lines and 3/4″ valves.

The suspension that parks this truck in the weeds is a custom solid beam/3 link setup and the semi truck wheels have been milled down to 22″ and 24″ (from 22.5″ and 24.5″ inches) giving Rob the ability to run Falken FK452 255/35zr22m, and 255/30zr24 tires.

Under the hood of this Chrysler Yellow behemoth lives a 7.3L Ford IDI diesel motor pulled from 1991 E350 (which also donated its front hubs and brakes) that’s been given a power upgrade via a Ford Power stroke turbo and and Dodge intercooler.

The motor now up on power the motor has no problem moving the truck down the road while powering the York engine driven compressor.

While it’s fairly easy for me to describe the modifications done to this vehicle I can’t really find the words to convey the presence that it has in person. Its size alone demands a certain type of respect.

Thankfully talented St. Catherines based photographer Steve Wharton (the man behind E11even:11: Photography) has been able to capture almost all of this trucks essence in these fantastic photos.

Steve and I have been waiting to work together for awhile now and 2011 should see a lot of collaboration between Stance Is Everything and E11even:11: Photography. If these photos are an example of the type of work he produces then we should all be in for a treat.

I am stoked to have a photographer like Steve on board and have no doubt that the kind of work he submits for this year will be second to none.

I hope you are as excited as I am.

Photo Credit: Steve Wharton – E11even:11: Photography

1977 International Loadstar 1600 – Complete Mods List

Chassis/suspension
-Full frame custom built
-3X6 ¼” wall, fully sealed and used as air tank (25 gallons)
-3 link front with custom solid beam suspension
-front hubs and brakes from 1991E350
-3 link rear with Sterling 10.25 differential
-10,000lb transport truck bags at all 4 corners
-3/8” air valves, ½” hard line
-digital air gauge
-york engine driven compressor
-5th wheel hitch
-dual fuel tanks custom built

Drivetrain
-7.3L Ford IDI diesel from 1991E350
-Ford E4OD transmission
-2001 Dodge intercooler
-2002Ford powerstroke turbo on custom manifolds
-massive transmission cooler
-turbo code injectors
-injection pump turned up and timing advanced
-5” exhaust to 5” slant cut stack
-3” intercooler piping powdercoated cream
-holley red electric fuel pump

Exterior
-floor and firewall from scratch
-suicide doors with fabricated hinges
-shaved door handles
-welded and smooth front body seams
-pedestal mount cab lights
-LED front and rear lighting
-HID headlights
-chrome visors over all lights
-cargo basket
-painted Chrysler classic yellow

Interior
-smoothed and painted dash
-seat from 1993 Chevy truck recovered by owners wife
-autometer gauges for- speedometer, tachometer, boost, egt, trans temp, oil pressure, coolant temp, volts, fuel level
-alpine stereo in glovebox
-soundstream 5 channel amp
-RE Audio 6.5” speakers
– 2 12” RE Audio subs
-triple trumpet air horns

Wheels and tires
Front wheels- 22.5” semi wheels milled to 22”
Front tires- 255/35zr22 Falken FK452
Rear wheels- 24.5” semi wheels milled to 24”
Rear tires- 255/30zr24 Falken FK452
Custom adapters

46 COMMENTS

  1. Great article man! .. I am really looking forward to the up and coming warm weathered months! and to bring some solid automotive visual entertainment for the stance is everything followers.

  2. Thats quite the behemoth! Would love to see something like this in person.

    Absolutely surreal photography, hope to see more work from E11.

  3. This is 1 sick rig. Rob did a sweet job on this truck. I know what u meen Dave. The 1st time I say it was @ the same show and I looked at it 4 a bout 1hr the 1st time.
    Nice job Rob.

  4. nice one dave this is hands down one of the coolest trucks on planet earth and it awsome to see such an indepth feature and i love the butterscoch color reminds me of old guitars and the atention to detail as abmerable i sooo wana go

  5. Saw this thing as Scrape last year, I had never layed my eyes on something so wicked. Really caught me off guard when I saw it amongst the other vehicles.

  6. This has GOT to be the ugliest color I have EVER seen on a vehicle. Looks like a fun, if worthless, project. I prefer to see trucks built for use.

  7. That truck is freaking awesome! Can I assume that was built by a Canadian, judging by the license plates? Just goes to show everyone the amazing builds and creativity that comes from the Great White North!

  8. I wanna see the build pics of this thing. I have a 1973 chevy c90 that i have alwats wanted to do this too!

  9. This is a beautiful creation…I totally respect the craftsmanship that went into this project. I will like to personally thank the team that put the big baby 2gether. It gave me so fantastic ideas for my 1964 GMC 6500 project…I will take several ques from this vehicle as I start my own old skool semi truck project. Thanks for sharing!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.